How to Reset an Electric Fireplace
To reset an electric fireplace, turn it off at the switch or breaker for about 30 seconds, then restore power. If the flames stay dark or the heat won't start, try the remote, the thermostat limit switch and the outlet before calling support.
On this page (10 sections)
- Why does an electric fireplace need a reset?
- How do you reset an electric fireplace step by step?
- Why won't my electric fireplace turn back on after a reset?
- How do you reset the remote and the thermostat?
- Can a power problem cause a fireplace that won't reset?
- Should you reset a hardwired fireplace or call an electrician?
- When should you stop resetting and look for a fault?
- Which tools help with a fireplace reset?
- What should you check before calling support?
- What is the reset rule to remember?
To reset an electric fireplace, cut its power for about 30 seconds and switch it back on. That clears the control board's memory the same way a reboot fixes a frozen device.
If the flames stay off or the heater won't start after that, the problem is usually the remote, the thermostat limit switch or the outlet. Work through those three checks before you assume the firebox is failing.
Why does an electric fireplace need a reset?
An electric fireplace resets because its control board gets stuck waiting for a command. Power interruptions, quick on-off presses and a locked remote can all leave it in a state where the buttons seem dead.
These fireplaces run on a small circuit board that stores the last setting, the flame color and the thermostat target. A power blip or a surge can scramble that memory, so the unit shows lights but ignores input.
A reset forces the board to reload its factory defaults. Most units come back in standby mode with the heat off, which means you re-enter your settings after the reboot.
Do the reset once. If the same fault comes back within a day, the cause is electrical or mechanical, and a second reset won't solve it.
How do you reset an electric fireplace step by step?
The reliable reset order is switch, breaker, wait, restore. Follow it in that sequence so you don't skip the board's full discharge.
- Turn the fireplace off with its own switch or remote, not just the thermostat.
- Cut power at the wall switch or the circuit breaker for the outlet.
- Wait about 30 seconds so the board drains and forgets the fault.
- Restore the breaker, then press the power button on the unit.
- Set the flame and heat again and watch for an error code.
Timer memory often clears on this cycle, so recheck any 1 to 8 hour sleep setting after the reset.

A center-find stud finder that helps when a hard reset means pulling the firebox out to reach the cord or the breaker behind the wall.
See it on AmazonWhat if the fireplace has no breaker of its own?
Use its plug or the wall switch when the unit shares a circuit. Unplugging a corded model gives the same 30-second drain as flipping the breaker.
Recessed and wall-mounted fireplaces often wire to a switch beside the unit or to a plug hidden inside the wall cavity. Find that point before you start, because pressing the front panel alone won't clear the board.
Why won't my electric fireplace turn back on after a reset?
The most common blocker is a tripped thermostat limit switch inside the heater. It cuts the element when the unit overheats and stays open until the firebox cools.
Give the unit 15 to 30 minutes with power off. Most limit switches close on their own once the sensor cools, then the heat works again.
A locked remote is the second common cause. Some fireplaces have a child-lock or panel-lock sequence that blocks both the remote and the touch buttons.
Hold the lock key for a few seconds, or pull the batteries and use the panel.
Unplug anything else on the same outlet and try again. A space heater or a vacuum sharing the circuit can starve the fireplace of current without tripping the breaker.
How do you reset the remote and the thermostat?
Reset the remote by replacing its batteries and clearing the lock, then reset the thermostat by cycling the heat mode. These are two separate fixes on most models.
For the remote, swap in fresh batteries and press the power key while standing close to the unit. If your model pairs, follow its pairing keys once, then test the manual buttons.
For the thermostat, switch the heat off, set the target to its lowest value, then raise it 5°F at a time. A target set below room temperature looks like a dead heater because the element stays off by design.
The Euhomy recessed model shows how the controls usually work. It runs on 750 W or 1,500 W, covers up to 400 sq ft, and offers a remote plus a touchscreen with a 62°F to 82°F range.

A 36 in recessed or wall-mounted firebox with both a remote and a touchscreen, so you can test one control against the other after a reset.
See it on AmazonCan a power problem cause a fireplace that won't reset?
Yes. Low voltage or a shared circuit can block a clean start.
The board needs a steady supply to boot, and a weak outlet gives it nothing to work with.
A 1,500 W heater pulls about 12.5 amps at 120 V, close to the limit of a standard 15 A circuit. Add a lamp or a charger on the same line and the draw pushes toward the trip point.
Move the fireplace to an outlet on its own circuit when you can. On a corded model, run an extension cord only as a temporary test, and use a heavy-gauge one.
The P3 monitor shows the draw in kilowatt-hours, so you can compare the fireplace against the rest of the room. Plug the unit into it and read the load while the heater runs.

Plugs between the fireplace and the outlet to count kilowatt-hours, so you can see whether the circuit is overloaded.
See it on AmazonShould you reset a hardwired fireplace or call an electrician?
Reset a hardwired fireplace only at its breaker. If the breaker trips again when you restore it, stop and call a licensed electrician.
Hardwired units have no plug to pull, and opening the case voids coverage on many brands. The Euhomy model, for example, comes with 2 years of technical support, and support can walk you through its own reset sequence.
Never reset a unit that smells of burning plastic or shows scorched wiring at the plug. That is a repair issue, not a control glitch.
When should you stop resetting and look for a fault?
Stop after two failed resets in one day. A repeated fault means a part is failing, and more resets just repeat the same result.
Watch for these signals before you keep pressing buttons:
- The heater cuts out within minutes every time.
- An error code flashes on the display after each reset.
- The flames work but the heat never does, or the reverse.
- The breaker trips each time the unit starts.
For a recessed model, check the cavity before you blame the board. Airflow matters, and our guide to recessed electric fireplace depth covers the clearances a firebox needs.
Which tools help with a fireplace reset?
A stud finder, a power monitor and a replacement firebox cover the three most common reset jobs. Each one answers a different question about why the unit won't start.
The stud finder helps when you need to reach the cord, the wall switch or a mounting bracket. The DEWALT locates stud centers through 3/4 in of wood and metal, with LED arrows and an audible alert.
A power monitor tells you whether the outlet is the problem. If the draw looks normal and the fireplace still won't boot, the fault sits inside the unit.
A new firebox is the last option, and it fits when the old one fails testing twice. Compare styles in our guide to electric fireplace inserts with logs if you want a flame look that reads like a real fire.
Weighing a swap against gas? Our breakdown of electric fireplace insert vs gas covers venting, install and running costs.
If you are starting fresh rather than fixing, our roundup of what are the best electric fireplaces sorts the models by room size and control type.
What should you check before calling support?
Note the model number, the error code and what you already tried. Support teams ask for that first, and a clear list saves a call-back.
Write down the reset steps you ran, how long the unit stayed off, and whether the heat or the flames failed. Add the outlet you used and anything else plugged into it.
A phone photo of the error display helps too. Many brands then send a replacement control board or a service visit under coverage.
What is the reset rule to remember?
For anyone searching how to reset an electric fireplace, the reset is a 30-second power cut, and a second failure is a repair signal. Try the breaker, the remote lock and the limit switch, then stop.
Pick the stud finder if you need to reach hidden wiring or a cord, the power monitor if you suspect the circuit, and the Euhomy firebox if you are replacing a unit that fails twice.
Keep the manual with the fireplace, because the reset sequence for your model beats any general advice. When the unit stays dark after a proper cycle, support is the next step, not a third reset.
Frequently asked questions
Does an electric fireplace need a reset after a power outage?
Usually yes. A brief outage can leave the control board waiting for a fresh signal, so switch the unit off at the breaker, wait half a minute, and turn it back on.
Most fireplaces return to standby with default settings after that.
Why does my electric fireplace keep tripping the breaker?
That points to too much draw on one circuit, not a control fault. A 1,500 W heater pulls about 12.5 amps at 120 V, so move it to a dedicated outlet and unplug other large loads before you reset anything.
Can a remote stop an electric fireplace from turning on?
Yes. A locked or unpaired remote can block the touchscreen, or a dead battery can leave you pressing a key that never sends.
Replace the batteries and use the manual controls to rule the remote out before resetting.
Is it safe to keep using an electric fireplace that won't reset?
Stop using it if the heat cutout trips twice or you smell burning plastic. Unplug the unit, note any error code, and contact the brand's support line rather than opening the case yourself.
About this guide: Our look at resetting an electric fireplace draws on maker specs, materials and what owners report. See how we research.



